bug su Hantek DSO5102P: differenze su misure tensione di rete in AC vs DC coupling
Re: bug su Hantek DSO5102P: differenze su misure tensione di rete in AC vs DC coupling
risposta da [email protected]
"Dear Franco.
Your device is probably under warranty, but you must contact the supplier / dealer from whom you purchased it to resolve the issue.
He should either replace or repair your oscilloscope while providing technical support."
non credo abbiano capito
FM
ps: rimandato indietro l'oggetto. cambio con un siglent
"Dear Franco.
Your device is probably under warranty, but you must contact the supplier / dealer from whom you purchased it to resolve the issue.
He should either replace or repair your oscilloscope while providing technical support."
non credo abbiano capito
FM
ps: rimandato indietro l'oggetto. cambio con un siglent
Re: bug su Hantek DSO5102P: differenze su misure tensione di rete in AC vs DC coupling
risposta da un post su un forum in lingua inglese
"Old oscilloscopes used an AC coupling capacitor in series with the input which was switched in and out of circuit using a relay. More modern designs tend to use a dual path input amplifier with the feedback implementing the AC coupling function because this is much easier to switch electronically, however this requires the time constants of the DC and AC paths to be matched for a flat frequency response above the transition region.
To verify this, look to see how the low frequency transient response changes between AC and DC coupling using a low frequency square wave. When AC coupling is used, a single pole (exponential) high frequency response should be present. A clean response for comparison purposes can be made by placing an approximately 0.19 microfarad capacitor in series with the x1 or x10 probe tip with DC coupling; 0.18 or 0.22 will work fine for testing purposes. In your examples, you can see the problem where the power line signal has a different shape when AC coupling is used.
Another way to test this is to compare the phase and amplitude of low frequency sine waves with one channel set to DC coupling and the other channel set to AC coupling. The difference should be a clean single pole response, but it won't be.
I consider any oscilloscope with this behavior to be defective by design; there is no excuse for it. I would return it for a refund if possible."
stessa nostra conclusione!
@Pier: aggiungo la entry nel CV, quindi!
"Old oscilloscopes used an AC coupling capacitor in series with the input which was switched in and out of circuit using a relay. More modern designs tend to use a dual path input amplifier with the feedback implementing the AC coupling function because this is much easier to switch electronically, however this requires the time constants of the DC and AC paths to be matched for a flat frequency response above the transition region.
To verify this, look to see how the low frequency transient response changes between AC and DC coupling using a low frequency square wave. When AC coupling is used, a single pole (exponential) high frequency response should be present. A clean response for comparison purposes can be made by placing an approximately 0.19 microfarad capacitor in series with the x1 or x10 probe tip with DC coupling; 0.18 or 0.22 will work fine for testing purposes. In your examples, you can see the problem where the power line signal has a different shape when AC coupling is used.
Another way to test this is to compare the phase and amplitude of low frequency sine waves with one channel set to DC coupling and the other channel set to AC coupling. The difference should be a clean single pole response, but it won't be.
I consider any oscilloscope with this behavior to be defective by design; there is no excuse for it. I would return it for a refund if possible."
stessa nostra conclusione!
@Pier: aggiungo la entry nel CV, quindi!
- Pier Aisa
- Amministratore
- Messaggi: 2540
- Iscritto il: ven 16 mar 2018, 9:43
- Località: Bologna
- Contatta:
Re: bug su Hantek DSO5102P: differenze su misure tensione di rete in AC vs DC coupling
Grande Franco !
Assolutamente da inserire nel CV !!! Potrai mettermi come testimone oculare con prove eseguite su altri samples ..... non è un baco da poco .... poi di concetto ... e vedrai che lo abbiamo su tutte le famiglie nuove .... e meno nuove.
Grazie !
Ciao
Pier
Assolutamente da inserire nel CV !!! Potrai mettermi come testimone oculare con prove eseguite su altri samples ..... non è un baco da poco .... poi di concetto ... e vedrai che lo abbiamo su tutte le famiglie nuove .... e meno nuove.
Grazie !
Ciao
Pier
Re: bug su Hantek DSO5102P: differenze su misure tensione di rete in AC vs DC coupling
Immagino che la risposta in inglese provenga dal noto forum australiano...
Errore/deviazione da specifiche nominali abbastanza grave.
Marco
Errore/deviazione da specifiche nominali abbastanza grave.
Marco
Re: bug su Hantek DSO5102P: differenze su misure tensione di rete in AC vs DC coupling
Morale della favola sicuramente i prezzi mostrati invogliano.... conviene comprare da un serio rivenditore italiano.... in caso di problemi glielo potete tirare sui denti.fmnardini ha scritto: ↑mer 14 apr 2021, 22:57 risposta da [email protected]
"Dear Franco.
Your device is probably under warranty, but you must contact the supplier / dealer from whom you purchased it to resolve the issue.
He should either replace or repair your oscilloscope while providing technical support."
non credo abbiano capito
FM
ps: rimandato indietro l'oggetto. cambio con un siglent
Re: bug su Hantek DSO5102P: differenze su misure tensione di rete in AC vs DC coupling
@Marco, si, quello
@tiziao: verissimo. il mio l'han già ricevuto "sui denti" da ieri, volendoti citare
grazie, saluti
FM
@tiziao: verissimo. il mio l'han già ricevuto "sui denti" da ieri, volendoti citare
grazie, saluti
FM
Re: bug su Hantek DSO5102P: differenze su misure tensione di rete in AC vs DC coupling
Come detto in precedenza con Pier recensiremo
https://www.mouser.it/ProductDetail/Ana ... WPSw%3D%3D
scheda che ha prestazioni di tutto rispetto e soprattutto fa le funzioni che promette (il sw è disponibile e funziona).
PS: dobbiamo ringraziare l' amico FAE/Stalker ADI De Andreis che ci ha segnalato questa piccola perla.
Re: bug su Hantek DSO5102P: differenze su misure tensione di rete in AC vs DC coupling
molto interessante. do un'occhiata.
grazie Tiziano!
saluti
FM
grazie Tiziano!
saluti
FM
Re: bug su Hantek DSO5102P: differenze su misure tensione di rete in AC vs DC coupling
sempre sul noto blog australiano, ora c'è chi prova Siglent e nota qualche differenza anche lì (ben diverse da Hantek, comunque).
link al post: https://www.eevblog.com/forum/testgear/ ... ac-vs-dc)/
saluti
FM
link al post: https://www.eevblog.com/forum/testgear/ ... ac-vs-dc)/
saluti
FM
Re: bug su Hantek DSO5102P: differenze su misure tensione di rete in AC vs DC coupling
Mi sa che ci vorrebbe una puntata di Pier per spiegare ai meno competenti come me il bug dalla teoria alla pratica come sa fare lui.
Nel frattempo faccio finta di aver capito
Nel frattempo faccio finta di aver capito
La strada è lunga e in salita ma c’è la faremo…….